
Alberta’s Occupational Health and Safety Code requires you to light your work site adequately, and it does not tell you what adequate means. There is no table of minimum light levels in the Code, no lux figure for formwork, no figure for finishing, no figure for a stair tower. The obligation is real and enforceable. The number is yours to set and yours to defend.
That asymmetry is the whole problem. Most compliance items on a concrete site arrive with a figure attached: a cover dimension, a strength at stripping, a distance from a power line. Lighting arrives with a standard of care and nothing else. After 38 years pouring concrete in this city, we have found the sites that handle lighting badly are rarely the sites that ignored it. They are the sites where nobody wrote down who decided, or on what basis.
What follows is what the Code says, where the numbers come from when it declines to give you one, and what the record needs to look like.
The short answer: Alberta sets the duty, not the level
Section 186 of the OHS Code is titled Lighting, and it sits in Part 12, General Safety Precautions, alongside section 185 Housekeeping and section 194 Vehicle traffic control. Part 12 is the part of the Code that governs the ordinary physical condition of a work site rather than a specific trade operation.
The Government of Alberta’s own explanation guide for Part 12 is blunt about the gap. It states that the OHS Code does not specify minimum lighting levels, and that employers must determine whether lighting at the work site is adequate for the tasks being performed. The guide then points employers to the Lighting Handbook published by the Illuminating Engineering Society of North America as the reference for what adequate looks like in practice.
So the structure is a performance obligation in the regulation, plus an external technical reference the regulator names but does not incorporate as law. Emergency lighting is handled separately and does carry prescribed requirements, through the building code rather than the OHS Code.
Two practical consequences follow. You cannot comply by pointing at a number, because there is no number to point at. And you cannot be found non-compliant for choosing the wrong number either, as long as you can show how you chose it. The exposure is in the absence of a process, not the choice of a value.
What a performance obligation asks of you in practice
When a code gives you a target, compliance is measurement. When it gives you a standard of care, compliance is reasoning that somebody else can follow. On lighting, that means four things.
- Identify the tasks, not the area. A slab pour at dusk contains several visual tasks at once: truck movement, chute handling, screeding, edging, and reading a laser or a grade stake. The hardest of those sets the level for the zone it happens in, not the average of all of them.
- Identify who is moving. Pedestrian travel ways, the approach to a stair or ladder, and the zone where powered mobile equipment backs up are where the consequence of poor light is not a bad finish but a struck worker.
- Pick a reference and name it. The province names the IES handbook. Recording which reference you used converts a judgment call into a documented decision.
- Verify after dark, on site. A lighting plan drawn at a desk in the afternoon is a hypothesis. The only honest test is standing in the work zone with the lights on.
The fourth point is the one that gets skipped, and it is the cheapest of the four.
Where the numbers come from when the Code will not give you one
Three sources are worth knowing about, and it is worth being precise about what each one is.
The IES Lighting Handbook. This is the reference the Alberta guide names. It is a technical publication, not legislation, and it is the defensible basis for a chosen level. If your safety program cites a level for a task, this is where that level should trace back to.
Other provinces’ regulations, as a sanity check only. Several Canadian jurisdictions do prescribe levels where Alberta does not. British Columbia sets normal lighting levels of 22 lux in low activity areas and areas housing machinery that are not regular task areas, 54 lux in high activity areas, and refers tasks requiring the ability to distinguish detail to a table in its regulation. Those figures help calibrate whether your own choice is in a sensible range. They are not Alberta requirements and should never be written into an Alberta site document as though they were.
Your contract. This is the one most people miss, and on public work it frequently outranks everything above.
On Alberta work zones, lighting is a contract item
If your pour sits in or beside a provincial highway work zone, lighting stops being purely a hazard assessment question and becomes a specification question.
Alberta Transportation’s Traffic Accommodation in Work Zones 2018 does not publish lux figures either. What it does instead is assign the decision. Under its Special Provisions process, the consultant has to confirm requirements for overhead illumination with the department representative and write those requirements into the contract Special Provisions. In other words, the number exists for your job, it is just set contractually rather than by regulation, and it is set before you mobilize.
The same document carries requirements that are concrete enough to design around:
- Flagging stations are to be illuminated by overhead lighting, and flagpersons working in darkness carry hand held red signal wands of sufficient brightness to be clearly visible to approaching traffic (section 5.6.1).
- Portable overhead lighting has to be aimed so that it does not blind road users, and the document asks for special attention to this (section 7.12). Type A low intensity flashing lights warn of obstacles; Type C steady burn lights delineate the travelled way on detours, lane changes and transitions.
- Where headlight glare from approaching traffic is a problem, screening may be required on protective barriers (section 7.13).
- Inspections carried out during darkness are to be done at least every two weeks, and also after significant changes or extreme weather, using the low headlight beam to confirm devices are visible. Records of those inspections are kept and provided on request (section 8.3).
Note what that last item really is. It is a prescribed inspection frequency for a condition that has no prescribed level. If you take one habit from this article onto a non highway site, take that one: inspect the lighting after dark, on a schedule, and write down that you did.
Equipment, travel ways and the lighting nobody budgets
Three places on a concrete site consistently come up short, and none of them is the place people light first.
Behind the equipment. Lighting the pour face is intuitive. Lighting the path a loader or pump truck reverses along is not, and that is where the serious incidents live. Powered mobile equipment in reduced light needs its own working lights plus a travel way lit independently of them, because an operator’s lamps do not illuminate what is behind the machine. Our note on operator training requirements for powered mobile equipment covers the competency side.
Vertical access. A stair tower, ladder landing or excavation ramp used at the end of a late pour is a fall exposure that worsens in the dark while the hazard assessment stays unchanged from the morning. A plan for working at height should say what happens to it after sunset; see our note on fall protection on a Calgary concrete pour.
The finish, after the light has gone. Flatwork finished under temporary lighting raked across the surface at a low angle looks different than it will at ten the next morning. Light the finishing zone from more than one direction if you can. It is not a safety requirement. It is the difference between a slab that passes a walk-through and one that does not.
Winter in Calgary turns this into a scheduling problem
By mid December, usable daylight in Calgary is short enough that a mid afternoon placement finishes in the dark as a matter of routine. Lighting stops being an incident response and becomes a line item in the pour plan, ordered with the pump and the blankets.
A pour that needs finishing after dark needs the lighting mobilized before the first truck, because nobody is setting up tower lights while a slab is going off. And the time it takes to light a work zone properly runs against a municipal noise clock, which is a separate constraint with its own permit and lead time. Our note on pouring concrete in winter covers the temperature side of a late season placement; the hours side is covered in our separate article on construction noise hours in Calgary.
How to make the decision defensible
A lighting record that holds up is short. One page is usually enough, and it contains five things:
- The tasks and travel ways you assessed, named.
- The level you selected for each, and the reference you took it from.
- The equipment you deployed to achieve it, including aiming and glare control.
- The date and time you verified it on site, after dark.
- The name of the person who made the determination.
That is the entire ask. Section 186 makes adequacy a question of fact, and a question of fact is decided on evidence. A site that can produce that page has evidence. A site that cannot is relying on the officer agreeing with its judgment.
Where this article stops
This is about lighting the work, under the OHS Code and provincial work zone requirements. It does not cover permanent emergency and exit lighting in a finished building, which is a building code matter belonging to the electrical and life safety design rather than the concrete scope. It does not cover permanent roadway or parking lot illumination design, or municipal light trespass and dark sky provisions, which vary by bylaw.
FAQ
If there is no number, how can a site be non-compliant? Because adequacy is a question of fact. An officer can conclude that the lighting provided was not adequate for the task observed. The defence is a documented determination, not a particular value.
Can we use British Columbia’s lux figures on an Alberta job? You can use them to check that your own choice is reasonable. Do not record them as the applicable requirement. British Columbia prescribes levels; Alberta does not, and an Alberta document citing a British Columbia figure as a requirement is describing the wrong jurisdiction.
Who decides lighting on a provincial highway work zone? It is set contractually. Alberta Transportation’s work zone document requires the consultant to confirm overhead illumination requirements with the department representative and include them in the contract Special Provisions.
How often should site lighting be checked? The provincial work zone standard requires inspections during darkness at least every two weeks, and after significant changes or extreme weather. That is a reasonable floor on any site that works after dark.
Talk to us before the pour plan is locked
Lighting is cheap when it is ordered with the pump and expensive when it is improvised at four in the afternoon. If you have a late season placement, a night pour, or a work zone where the illumination requirement is about to be written into your Special Provisions, bring it up while the sequence is still being drawn.
Across 52,000+ projects we have placed concrete in most conditions this city produces, a lot of them after dark. If you are planning commercial work this winter, our commercial concrete team can walk the sequence with you and say where the light has to be before anyone mobilizes.
Sources
- Government of Alberta, Occupational Health and Safety Code 2009 Part 12 Explanation Guide, General Safety Precautions (section 186 Lighting): https://open.alberta.ca/dataset/757fed78-8793-40bb-a920-6f000853172b/resource/16b5e158-0cca-4308-ad00-aee67a3283ae/download/4403880-part-12-general-safety-precautions.pdf
- Government of Alberta, Occupational Health and Safety Code, Part 12 General Safety Precautions: https://search-ohs-laws.alberta.ca/legislation/occupational-health-and-safety-code/part-12-general-safety-precautions/
- Alberta Transportation, Traffic Accommodation in Work Zones 2018: https://www.transportation.alberta.ca/Content/docType233/Production/TAWZ2018-2.pdf
- OHS Insider, provincial comparison of occupational health and safety lighting and illumination requirements: https://ohsinsider.com/around-the-provinces-ohs-requirements-for-workplace-lighting-illumination/