Mon–Fri 8:00am – 5:00pm 135, 5065 13 St SE, Calgary (403) 217-4888
COR Certified · BBB A+

Parkade Repairs in Calgary: The Permit You Qualify For by Proving What You Are Not Doing

Parkade Repairs in Calgary
Table of Contents
Parkade Repairs in Calgary

A parkade repair permit in Calgary is granted on the strength of a negative finding. The application does not ask you to prove the repair works. It asks a professional engineer to put in writing that structural repairs are not required, and the entire permit stream you are trying to use depends on that one sentence existing.

That is an unusual way to qualify for anything, and it catches crews out. Most permit applications are built around what you intend to do. This one is built around what you are not doing. After 38 years pouring and repairing concrete in this city, we have watched more parkade jobs stall on the wording of that letter than on anything that happens with a chipping hammer.

The stream opens only if every component you are touching is non-structural

The City’s Complete Application Requirement List for Parkade Repairs sets two conditions, and both have to apply. The work must be limited to repairing or maintaining only the non-structural components of an existing parkade. And the work must make no changes to the building’s mechanical or electrical systems.

The City’s own examples of non-structural components are narrow and worth reading literally:

  • Wear course
  • Moisture barriers
  • Drainage components
  • Architectural finishes

That list is the whole gate. A topping replacement, a membrane re-do, a trench drain swap, a repaint of the soffits — those sit inside it. The moment the scope reaches past them into the slab that is carrying the cars, you are not in this stream any more, and no amount of rewording gets you back in.

Note also what the City does not do on that page: it never defines “repair” as against “alteration” beyond those two conditions. There is no square-metre threshold and no dollar threshold. The boundary is entirely about which components are involved.

Section D is a letter about an absence, and it is the application

The supporting document the City calls Section D is written verification from a professional engineer confirming that structural repairs are not required.

The direction of the proof matters. The engineer is not certifying a repair design; the engineer is certifying that the condition of the parkade does not demand one. That is a conclusion about the structure, reached by someone who has looked at it, and no engineer writes it casually.

Two practical consequences follow, and they both land on the contractor:

The investigation happens before the application, not after. Somebody has to establish the condition of the deck well enough that a professional will sign a statement about it. On a parkade with spalling at the drive lanes and rust staining under the slab, that is not a walk-through — it is sounding, selective removal and usually testing. If you are deciding what testing earns its place, our note on what each non-destructive method actually proves covers which tool answers which question.

If the engineer cannot write the letter, the project changes shape. It leaves the quick-release category and becomes a commercial alteration with structural scope, carrying the professional involvement, drawings and review that come with that. Budget and schedule both move. Find that out while you are still pricing — which is why Section D is the first question on a parkade, not a closing formality.

The floor plan has to be stamped, and it has to show the sequence

Section C asks for one copy of a complete architectural set, including a site or key plan, at a preferred scale of metric 1:100 or imperial 1/4″ = 1’0″.

The site or key plan has to show the exact location of the tenant space within the building, and the unit number.

The floor plan has to be stamped by an architect or engineer registered in Alberta, and it has to show five things:

  1. The written scope of work
  2. The sequence of repair and/or maintenance
  3. The location and extent of the proposed work
  4. Construction details for all proposed repair and maintenance work
  5. Any restrictions on parkade use during the work

Items 2 and 5 are the ones that get left off, and the hardest to add later. A parkade is an operating asset: stalls are rented, access is contractual, and the building cannot usually surrender the whole deck at once. So the City is asking, on the drawing, for the staging — which bays come out when, and what the building loses while they are out.

That is a drawing requirement, but really a construction-planning one: it sets where the pours meet. If the staging on the stamped drawing does not match how the deck can actually be isolated and re-tied, you either build something other than what was permitted or you go back for a revision. Where staged pours meet matters for the same reasons movement joints matter anywhere else in a slab.

Material specifications are a separate submission unless they are already in the drawings

Section F asks for one copy of material specifications, stamped by the architect or engineer of record — and says plainly that it is not needed if the specifications are already included in the floor plans.

That is a small mercy with a catch. Rolling the specifications into the drawing set removes a submission, but the stamped drawing now carries the product selection. Change the membrane or the repair mortar on site and you have changed a stamped document.

Section E asks for a completed Asbestos Abatement Form — a City requirement independent of what the repair scope is.

Quick release does not mean planning is finished

The City lists parkade repairs twice: once as a change to an existing building, and once as a category eligible for quick release. The second listing carries an explicit qualifier — quick release still requires a Land Use review.

The parkade requirement list says the same thing from the other direction: under Land Use Bylaw 1P2007, a development permit is generally required unless the development is exempt.

So the fast stream is fast on the building-permit side only. Planning approval has to be in place before a building permit is issued, and a permit filed ahead of its approvals sits on hold until they land. On an interior-only parkade repair the Land Use review is usually the short part — but it is a step, and not the step the word “quick” describes.

Two City sources, two clause numbers, for the same question

Here is a wrinkle worth knowing before you argue it with anyone.

Both City sources tell you that an architect or professional engineer may be required and that plans must then be stamped. They point at different places in the code for the test. The commercial alterations page sends you to Building Code Division C, Section 2.4.2. Building Advisory B23-005 sends you to the National Building Code (Alberta Edition), Division C, Section 2.4.1.

We are printing both rather than picking one or splitting the difference. B23-005 is the more specific document — a Building Advisory accepted by the Codes and Standards Technical Interpretation Committee on August 1, 2024 and issued by the Chief Building Official — and it states on its face that it cannot be used as an official interpretation of the bylaws, codes and regulations. So the honest instruction is: confirm the clause with the Planning Services Centre for your scope, and do not let a citation in a web page carry a professional-involvement decision.

For a parkade repair the point is close to moot, because Section D already puts a professional engineer in the file and the floor plan already needs a stamp. It matters on jobs where someone is trying to establish that no professional is required at all.

The resubmission deadlines are not one deadline

Three different day counts attach to this application, and they are not the same clock.

  • The parkade requirement list, under Building Permit Bylaw 64M94: an application may be refused if adequate information is not supplied within 90 days of receipt, and fees paid are not refunded.
  • B23-005, prescreen stage: a failed prescreen gets written notice and 30 days to resubmit.
  • B23-005, detailed review stage: written notice and a total of 90 days to submit the outstanding information, with reminders at 30 days and 60 days. The 60-day reminder is the final notification and gives 30 days to submit everything.

The commercial alterations page describes the same shape differently again — refusal if missing information is not supplied within 90 days, then 30 days to resubmit.

The useful takeaway is not a reconciled number. It is that the short clock is the prescreen one, it runs before anyone has read your drawings in detail, and it is the one that catches an application submitted with a placeholder. The City will not accept plans stamped “not for construction,” “preliminary,” or “for permit purposes only,” and asks that no personal information appear on any plans — omitting that can itself render the application incomplete.

What this article does not decide

This is a permit-stream article. It does not tell you how far the deterioration goes, and that is deliberate, because the two questions have different answers and different owners.

How deep the repair reaches — whether a spall is a partial-depth patch or comes out through the slab, and what the condition of the reinforcing steel does to that decision — is scoped separately, and we have written that up in partial-depth versus full-depth repair. Work that question first on a parkade. Its answer is what determines whether the Section D letter can exist at all, and therefore which permit you are filling in.

Fees are the other thing this article will not estimate. Building permit fees vary with the construction cost, and the City’s current fee calculator is the only number worth quoting back to an owner.

Parkade repair permits: FAQ

Do I need a building permit to repair a parkade in Calgary? Yes. The City lists parkade repairs as a change to an existing building, and a permit is required for alteration, relocation, repair or demolition of structural and non-structural walls. Wholly cosmetic work — painting or furniture — is the exception.

What makes a parkade repair eligible for quick release? The work has to be limited to repairing or maintaining only non-structural components of an existing parkade, and it has to make no changes to the building’s mechanical or electrical systems.

What is the engineer’s letter for? It is written verification from a professional engineer that structural repairs are not required. Without it the application is incomplete, and if an engineer will not write it the work does not belong in this permit stream.

Does quick release skip the planning side? No. Quick release still requires a Land Use review, and under Land Use Bylaw 1P2007 a development permit is generally required unless the development is exempt.

Who has to stamp the drawings? The floor plan must be stamped by an architect or engineer registered in Alberta. Material specifications, if submitted separately, must be stamped by the architect or engineer of record. A building permit expires 180 days after issue; a contractor trade permit, 330 days.

Talk to us before the engineer writes the letter

The cheapest hour on a parkade job is the one spent establishing condition before anyone drafts Section D. Get that wrong and you either carry a scope the permit does not cover, or you pay for a review stream you did not budget.

We have been repairing concrete in Calgary for 38 years, across more than 52,000 projects, and we are comfortable telling an owner the deck needs more than a wear course when that is the answer. Bring us in while the investigation is still being planned — see concrete repair for how we scope this work.

Sources

  • City of Calgary, Complete Application Requirement List: Parkade Repairs (quick release)
  • City of Calgary, Changes to existing buildings — commercial alterations
  • City of Calgary, Building Advisory B23-005, Building Permit Complete Application (accepted by CSTIC August 1, 2024)